Vanes printed to fit your arrow
Every fin is part of one sleeve, made for your exact shaft. Two rings of glue, slide it on, and you're done. No jig, no clamps, no lining up vanes by hand.
- Tell us your arrowEvery sleeve is sized to your shaft.
- Pick a profile and twistOr answer a quick question or two and get a suggestion.
- Glue it and slide it onAbout a minute per arrow.
Example: Easton · Axis 5mm · 340
Want a shape we don't list? Custom profiles are still in development. Email us your idea or a sketch and we'll check whether it prints.
Click the graph to add a point, drag points to reshape, or type exact values. Nock end is on the left. Arrow keys nudge the selected point (Shift for bigger steps). Red sections are too steep to print.
Why a slide-on sleeve
No jig, no clamps
All the fins are one piece, already spaced and angled. Glue it, slide it on, and move to the next arrow.
Spin built in
Helical or offset is printed into the sleeve, so every arrow in your quiver comes out the same.
Fix it in the field
Tore a fin? Cut the sleeve along a fin with a utility knife, peel it off, clean off the old glue and slide on a new one. No stripping the whole arrow.
Questions
What's in a pack?
One sleeve per arrow, and each sleeve carries all of that arrow's fins. A pack of 6 fletches 6 arrows, 12 fletches 12, and 18 fletches 18.
How do I pay?
By card on Stripe's secure checkout page. Nothing is charged until you finish there.
How long until my order ships?
Every order is printed for you. Most ship within 7–10 business days of payment. Need it sooner for a hunt or a shoot? Say so in the order notes and we'll do what we can.
What if a sleeve arrives damaged?
Email photos of the damage to within 14 days of delivery and we'll ship you replacements.
What if it doesn't fit?
We check the arrow you enter against the maker's published shaft size before we print. If a sleeve still doesn't fit, email us within 14 days of delivery with your arrow and shaft size. If we printed it wrong, we reprint it free. If the size entered was off, we'll work out a fix with you.
What are they made of?
A flexible, rubber-like plastic, printed to order for your shaft. A fin that gets folded over springs back instead of cracking.
How snug is the fit?
Each sleeve is printed to the shaft size you give us, with a small built-in gap for glue: snug enough not to wobble, loose enough to slide on. If your shaft is an unusual size, mention it in the notes and we'll check with you before printing.
Which profile and twist should I pick?
Use Get a recommendation in the builder for a suggestion, or see Profiles for a quick picker and every spec. The Fletching guide explains twist, direction and vane count.
What glue do I use?
A fast-setting fletching glue, the kind that grabs in seconds. That's what we install and test with. Slow-setting solvent cements haven't been tested. See Install for how much to use and the one-smooth-slide method.
Will they work with my rest?
We've shot them from drop-away rests and full-capture brush rests. Blade (launcher) rests haven't been tested yet, so if you shoot one, check that the sleeve passes the blade cleanly before you rely on it. Like all vanes, they aren't made for shooting off the shelf of a traditional bow.
How do I line them up with my nock?
There's no marked fin. Turn the sleeve so its fins sit the way your other arrows are fletched, and make sure no fin will touch your rest, cables or string. With four fins that usually means an X, with no fin pointing straight up or down when the arrow is nocked.
Checkout
Your order
Profiles
Five shapes, drawn to true scale, with every number. Not sure which you need? Start with what's on the front of your arrow.
Which profile?
Start here for heads 1⅛in and smaller, at 3° helical. Wider heads, or not sure: RANGE. A bigger profile works too; we wouldn't go smaller.
2° helical for mechanicals, 1° offset for field points outdoors. GHOST for target shafts under 0.215in.
Our largest profile, at 3° offset, for shafts 0.32in and up. On regular shafts indoors, IMPACT at 3° offset.
Still not sure? and it picks a profile and twist for you.
Side by side
Drawn at true scale, standard length. Heights are measured from the arrow shaft. Steering area is one fin.
Specs
Weight is the whole sleeve, every fin for one arrow, at standard length on a 0.300in shaft; a 0.265in shaft runs about 1 grain lighter. Every profile can be shortened; the builder shows each one's shortest length.
Compared with individual vanes
A sleeve weighs about the same as three individual vanes of similar size. Compare the “Three” column here with “Weight, 3 fins” in the spec table above. Heights for individual vanes are measured from the vane's base, which sits on the shaft, so they compare directly with ours.
| Vane | Length | Height | Each | Three |
|---|---|---|---|---|
| Short, tall vane | 2.0in | about 0.55in | about 6 gr | about 18 gr |
| Mid-length vane | 2.5in | about 0.4in | about 6 gr | about 18 gr |
| Long vane | 3.0in | about 0.5in | about 9 gr | about 27 gr |
Typical published figures for popular plastic vanes, rounded. Exact numbers vary by brand and model.
Fletching guide
How vane size, twist, direction and count change the way an arrow flies, in plain words, with the setups we'd start from.
Size: height and length
Area (length × height) sets how much a vane steers. A taller vane steers more for its size, but it is louder and needs more rest clearance. A longer, lower vane with the same area is quieter.
Shaft size matters at the extremes: fat indoor shafts need big vanes, thin target shafts small ones. Across normal hunting shafts, profile and twist matter far more.
Twist: straight, offset and helical
Twist is what makes an arrow spin, and spin evens out small flaws in flight. More twist means more spin and a little more drag.
Our degrees are the fin's angle to the shaft, seen from above. The builder also shows how far each fin wraps around your shaft.
| Point | Where we'd start |
|---|---|
| Field points, outdoors (3D, field, target) | Offset 1° |
| Field points, indoors | Offset 3° |
| Mechanical broadhead | Helical 2° |
| Fixed-blade broadhead | Helical 3° |
We keep broadhead twist the same at every distance. For field points at long range, less twist means less drag.
Helical goes up to 4° on vanes 2.25in and shorter, and 3° on longer ones. ANCHOR goes up to 2° at any length. Offset comes in 1° to 3° on every profile.
Right or left?
Right spins the arrow clockwise as it flies away from you; left spins it counter-clockwise. Neither is more accurate. We default to right because it's the most common setup, especially with fixed-blade broadheads.
Shooting single-bevel heads? Match the twist to the bevel: right for a right-bevel head, left for a left-bevel head. Whatever you pick, keep every arrow in your quiver the same.
3 fins or 4?
Three fins is the standard. Four adds about a third more surface for more steering, with a little more drag.
If you go to four, consider a smaller profile so the total area stays about the same: four RIDGE is about the same area as three IMPACT, and four IMPACT about the same as three RANGE.
Weight and FOC
A sleeve weighs about 13 to 30 grains with three fins, depending on the profile. The spec table lists each one, with typical individual vanes below it for comparison.
Weight at the back of an arrow lowers its front-of-center (FOC): how far the arrow's balance point sits ahead of its middle, as a percentage of arrow length. Easton suggests 10–15% FOC for hunting arrows. If you're switching from lighter vanes, check your FOC and your broadhead flight.
Bows and rests
We've shot our sleeves from drop-away rests and full-capture brush rests. Blade (launcher) rests haven't been tested yet, so if you shoot one, check that the sleeve passes the blade cleanly before you rely on it. Like all vanes, they aren't made for shooting off the shelf of a traditional bow; feathers are the norm there.
There's no marked fin. When you slide one on, turn it so its fins sit the way your other arrows are fletched, and check that no fin will touch the rest, cables or string. With four fins that usually means an X, with no fin pointing straight up or down when the arrow is nocked.
Glossary
- Shaft OD
- The outside diameter of the arrow shaft. Every sleeve is printed to it.
- Nock throat
- The bottom of the nock's groove, where the string sits. Vane placement is measured from here.
- Fin
- One blade of fletching. Each sleeve carries all the fins for one arrow.
- Cock vane
- On arrows fletched one vane at a time, the odd-colored vane used to nock the arrow the same way every time. Our sleeves are one color, so there isn't one.
- Offset
- Straight fins set at an angle to the shaft.
- Helical
- Fins that curve around the shaft.
- Grains
- The unit arrow parts are weighed in. 15.4 grains is one gram.
- FOC
- Front-of-center: how far an arrow's balance point sits ahead of its middle, as a percentage of the arrow's length.
- Spine
- How much a shaft bends under a set load. A lower number is stiffer.
- Mechanical broadhead
- Blades fold in flight and open on impact, so it flies close to a field point.
- Fixed-blade broadhead
- Blades are always open, so it needs more steering from the back of the arrow.
- Single-bevel
- A broadhead sharpened on one side of each blade, made to rotate one way.
- Wraps
- Thin vinyl stickers around the back of the shaft. Tell us if you use them, and we size the sleeve to fit over a standard wrap.
Slide on. Peel off.
About a minute per arrow. All you need is glue and, for removal, a utility knife.
Putting a sleeve on
Before you start
- Start with a clean shaft. Remove any old glue, vane residue, dirt or oil so the shaft is smooth all the way around. Leftover glue can stop the sleeve partway down the shaft, and it keeps the new glue from bonding.
- Glue: use a fast-setting fletching glue, the kind that grabs in seconds. That's what we install and test with. Slow-setting solvent cements haven't been tested.
- Pick your spot. Most hunters put the back of the sleeve 1 to 1½ inches from the nock throat, the bottom of the nock's groove. Check that it clears your rest and doesn't touch your face at full draw.
- Line it up with your nock. There's no marked fin. Turn the sleeve so its fins sit the way your other arrows are fletched, and so no fin will touch the rest, cables or string. With four fins that usually means an X, with no fin pointing straight up or down when the arrow is nocked. Hold it that way as you slide.
- Using wraps? Press them flat first. Run your fingers up and down the wrap a few times to make sure it's fully pressed down. Then run the back of your fingernail along the seam where the wrap overlaps itself, a few passes. Flattening that seam lets the sleeve slide over it cleanly.
- Thumb: pinch the shaft between your thumb and finger at the front mark and slide the sleeve up against your thumb.
- Electrical tape: if the sleeve is a snug fit, wrap a few turns of electrical tape just in front of the front mark. It stops the sleeve in the right spot and frees up both hands for the slide. Peel the tape off once the sleeve is on.
- Mark the spot
Mark the shaft where the front and back of the sleeve will sit.
- Glue at the back mark
Put a thin bead of glue around the shaft at the mark nearest the nock, right on it or just inside it. Match the amount used in the video.
- Glue in the middle
Put a second bead roughly halfway between the two marks.
- Slide it on in one smooth, quick motion
From the nock end, push the sleeve all the way to the front mark in a single, steady motion. Don't stop, and don't go slowly.
- Done
That's it. On to the next arrow.
- Too much makes the sleeve drag, so it's more likely to stall partway, and the extra squeezes out the ends.
- Too little can set too quickly while you're sliding the sleeve on.
Replacing a damaged sleeve
- Cut along a fin
Run a utility knife down the length of the sleeve, right beside one fin. Keep the blade shallow: you're cutting the sleeve, not the shaft.
- Peel it off
The sleeve comes away in one piece. The other arrows don't need touching.
- Clean and check the shaft
Remove the leftover glue so the shaft is smooth all the way around, then look it over and run a fingertip along it. If the knife nicked or cut the shaft, don't shoot that arrow.
- Slide on a new one
Same as putting one on. Done.
See every color
Real prints, not renders. Every color we stock on the ANCHOR profile, and the sample pack we send to clubs.
We're shooting every color now. In the meantime, the 3D preview on the Build page shows your exact vane in your color.
Colors
Every color shown on the ANCHOR profile. Tap a photo to see it larger.
Club sample pack
The kit we hand to archery clubs around the Fargo area: all five profiles, each in an offset and a helical, printed for real arrows so members can see and feel the difference. Run a club and want one? Email us.
Reviews
Made by a shooter, not a factory
Why this exists
This started with two annoyances, not a business plan: showing up to hunt or shoot with a torn vane and no fletching jig to fix it, and scratching arrow shafts nearly every time I stripped off old vanes.
So the requirement was simple. It had to go on and come off without a jig, without scratching anything, and fast enough to do standing in a field. Glue, a knife, about a minute: slide a new sleeve down the shaft, and if one gets torn up mid-hunt, cut it off, peel it away and slide the next one on.
I'm Isaac, and I design and print every one of these myself. It turned into a business when I realized other people were dealing with the same problem, and once the design worked there wasn't a good reason to keep it to myself.
Fit first
Every sleeve you order here is built for the shaft and specs you give us, not pulled off a shelf. An unusual shaft size, wraps, a particular twist for your broadhead: that isn't a special request, it's how every order works.
Your sleeve is fit to your arrow before it's printed, not the other way around.
This is a small, made-to-order shop. Your order gets real attention, and I stand behind every one that ships.
Tested before it's sold
I don't release a profile I haven't printed and shot myself. If it doesn't group well, fly quiet and hold up on impact, it doesn't go up for sale.